Mark 2 / 240 / 340

SMITHS ammeters in classic British cars were usually rated at 30 amps, fine for the original generator, but in case you have upgraded to an alternator, you'll need one that can handle the extra amperage.This one is made by Caerbont, the successor to the SMITHS company, on original factory tooling in the same shop that the old company occupied. It comes complete with mounting bracket and light.NOT FOR USE WITH ALTERNATORS OF GREATER THAN 60 AMPS!

This is an excellent used spare wheel hold-down clamp for a Jaguar E-type of small saloon, including Mark I, Mark 2, 3.4 or 3.8S, 420, or Daimler 2 1/2 or 250. It has been stripped, cleaned and painted black.

This is a new Lucas-type SRB316 starter solenoid, but not supplied by Lucas or in a Lucas box.  It is the correct starter solenoid for most six-cylinder Jaguars, including XK120, XK140, XK150, E-type, Mark I, Mark 2, Mark VII, Mark VIII, Mark IX, Mark IX, S-type, 420, 240, 340, Daimler 2 1/2, 250, SP250, as well as early MGB, Triumph TR2, TR3, TR4, big Healey, Land Rover, and many others.Genuine Lucas SRB316 solenoids are also available; see Related Products below. ...

These kits are now in stock. This is a good reproduction of a kit which was made in the 1960s and 1970s to adjust, tune and synchronize SU carburetors. We have a set of these and use them often. Well, as often as we bother to tune the SU's, that is, which isn't as often as we should..... Includes a jet wrench, instruction booklet and enough special carb tools to balance two or three carburetors.

This is a very nice used grease gun, correct for Jaguar XK150, XKE, E-type, Mark 2, Mark IX and X, S-type, Daimler 2 1/2 and other Jaguars of the 1960s and late 1950s. It is in very good original condition.

All Jaguars of the 1950s, 1960s, and 1970 with wire wheels came with a Thor 2-lb. copper and rawhide hammer for the wire wheel knockoffs. This is the correct one for an XK120, XK140, XK150, Mark I, Mark II, E-type, XKE, Mark VIII, Mark IX, Mark X, 240, 340, S-type 2.4 and 3.8, and most Daimlers.It's in new, perfect condition, 100 percent concours correct and made by the original manufacturer in England, exactly as original.We also have copper 1-lb hammers and plywood and steel knock off...

This lovely little tyre gauge will fit your vintage Jaguar or Rover tool box or roll perfectly. It is a generic, unlabelled gauge, marked only MADE IN ENGLAND but it's the right size and shape for a Jag or Rover kit. It's also a lot less money than the correct gauge.This one is pretty much identical to a Dunlop 6J apart from the Dunlop logo. It's 4 1/2 inches long.We do sell Jaguar tyre gauges, both Dunlop 6 and 6J and the style with JAGUAR and the wings logo, in case you want one of those....

Jaguars made in the 1950s, 1960s and 1970s(XK120, XK140, XK150, Mark 2, 340, E-Type, XKE) came with high quality tool kits. There were several types of 4-inch adjustable spanners fitted to Jaguar kits from about 1955 through the 1970s, all marked "JAGUAR." These are very rare and expensive. This is a nice new 4-inch adjustable spanner, not correct for any Jaguar factory kit, but it fits perfectly and would make a fine substitute for somebody not concerned with building a concours-quality kit....

Jaguar XJ cars came equipped with a comprehensive too kit from the factory. This is a particularly complete and nice example. The tools and spare bulbs and fuses appear to be original and correct. We believe this kit came from a so-called "XJ40" Jaguar, which might have been either an XJ6 or an XJ12. It would be a cool addition to any old Jaguar, though. It contains both metric and fractional wrench sizes.

This Mark 2 Jaguar upper steering column cover has been cleaned and repainted. It is in excellent condition. We also have an NOS lower housing, but please email us for details.

This is a new forged steel 3/8" 12-point drive socket set, made by the venerable King Dick Tool Company in England. Included are Whitworth sizes 1/8" through 1/2". We use these sockets regularly in our shop and have found them to be of excellent quality.Whitworth fasteners were used on virtually all English cars and motorcycles through the 1970's.

This is a new drop-forged steel combination-end spanner set including Whitworth sizes 1/8" through 1/2". We use these wrenches regularly in our shop and have found them to be of good quality.Whitworth fasteners were used on virtually all English cars and motorcycles through the 1970's.