E-Type

This laminated wooden wrench fits over 52mm Jaguar knock off spinners for tightening and loosening and protects them from hammer marks.We also stock an alternative design: long steel knock off wrenches. For these or 42 mm plywood knock off wrenches to fit MG, Austin-Healey, Triumph, etc.; knock off hammers and knock off spinners, see Related Products below.

SMITHS ammeters in classic British cars were usually rated at 30 amps, fine for the original generator, but in case you have upgraded to an alternator, you'll need one that can handle the extra amperage.This one is made by Caerbont, the successor to the SMITHS company, on original factory tooling in the same shop that the old company occupied. It comes complete with mounting bracket and light.NOT FOR USE WITH ALTERNATORS OF GREATER THAN 60 AMPS!

This is an excellent used spare wheel hold-down clamp for a Jaguar E-type of small saloon, including Mark I, Mark 2, 3.4 or 3.8S, 420, or Daimler 2 1/2 or 250. It has been stripped, cleaned and painted black.

This is a new SRB316 starter solenoid, but no longer supplied by Lucas or in a Lucas box.  It is the correct starter solenoid for most six-cylinder Jaguars, including XK120, XK140, XK150, E-type, Mark I, Mark 2, Mark VII, Mark VIII, Mark IX, Mark IX, S-type, 420, 240, 340, Daimler 2 1/2, 250, SP250, as well as early MGB, Triumph TR2, TR3, TR4, big Healey, Land Rover, and many others.

This is an excellent quality horn push and steering wheel center. Most of the ones we have seen lately have been defective, with tiny cracks and sloppy details. This one is quite good, although it is a reproduction.It is correct for Series I and Series II 3.8 and 4.2 litre 6-cylinder Jaguar E-types, but not for the V-12 cars.

This is a good reproduction of a kit which was made in the 1960s and 1970s to adjust, tune and synchronize SU carburetors. We have a set of these and use them often. Well, as often as we bother to tune the SU's, that is, which isn't as often as we should.....Includes a jet wrench, instruction booklet and enough special carb tools to balance two or three carburetors.

This is a very nice used grease gun, correct for Jaguar XK150, XKE, E-type, Mark 2, Mark IX and X, S-type, Daimler 2 1/2 and other Jaguars of the 1960s and late 1950s. It is in very good original condition.

All Jaguars of the 1950s, 1960s, and 1970 with wire wheels came with a Thor 2-lb. copper and rawhide hammer for the wire wheel knockoffs. This is the correct one for an XK120, XK140, XK150, Mark I, Mark II, E-type, XKE, Mark VIII, Mark IX, Mark X, 240, 340, S-type 2.4 and 3.8, and most Daimlers.It's in new, perfect condition, 100 percent concours correct and made by the original manufacturer in England, exactly as original.We also have copper 1-lb hammers and plywood and steel knock off...

High quality reproduction of the original vinyl tool roll for your XK140, 150 or E-type. This is beautifully made, with the correct leather strap and buckle, and all the pockets properly sized, with correct off-white lining. This is from a supplier that is new to us, but the product is excellent. Our previous supplier no longer makes tool rolls for Jaguars. Jaguar PN C5578.

Jaguars made in the 1950s, 1960s and 1970s(XK120, XK140, XK150, Mark 2, 340, E-Type, XKE) came with high quality tool kits. There were several types of 4-inch adjustable spanners fitted to Jaguar kits from about 1955 through the 1970s, all marked "JAGUAR." These are very rare and expensive. This is a nice new 4-inch adjustable spanner, not correct for any Jaguar factory kit, but it fits perfectly and would make a fine substitute for somebody not concerned with building a concours-quality kit....

This is a new forged steel 3/8" 12-point drive socket set, made by the venerable King Dick Tool Company in England. Included are Whitworth sizes 1/8" through 1/2". We use these sockets regularly in our shop and have found them to be of excellent quality.Whitworth fasteners were used on virtually all English cars and motorcycles through the 1970's.

This is a new drop-forged steel combination-end spanner set including Whitworth sizes 1/8" through 1/2". We use these wrenches regularly in our shop and have found them to be of good quality.Whitworth fasteners were used on virtually all English cars and motorcycles through the 1970's.